DRYLOK® Concrete Stain and Toner

DRYLOK® Concrete Stain and Toner

DRYLOK® Concrete Stain and Toner preserves and accents natural texture or embossed stamping patterns when used to colorize bare or colored concrete, and hide minor surface stains and blemishes.

DRYLOK® Concrete Stain and Toner is quick-drying, water-based, semi-opaque and easy to apply. It dries to a non-slip, flat finish.

DRYLOK® Concrete Stain and Toner Application

Quick Overview

DRYLOK® Concrete Stain and Toner lets you achieve a layered, faux or single-color look more quickly than the use of acid stains. This water base, semi-opaque formulation can be used on aging and new concrete, alone or in combination with other colors to achieve a stunning decorative finish. Varying looks will be achieved during each application, depending on the smoothness or porosity of the surface.

Product Features:

  • 3 Ready-mixed colors and a tint base for 15 tintable colors
  • Apply to interior/exterior concrete surfaces
  • Sizes: gallon
  • Coverage: 300-400 square feet per gallon depending on the porosity of the surface
  • Application tools: spray, roller, brush
  • Dry time: 1 hour
  • Coats: 1

View DRYLOK® FAQ

Surfaces

  • Concrete pool decking
  • Concrete porches
  • Concrete walkways
  • Basement and garage floors

Ready-Mixed Colors

Concrete Gray Concrete Gray
Cream Cream
Maple Brown Maple Brown

Please note, colors are RGB web approximations of the actual shades.

Tints

Autumn Sun Autumn Sun
Battleship Gray Battleship Gray
Blue Stone Blue Stone
Desert Stone Desert Stone
Dusty Charcoal Dusty Charcoal
Forest Green Forest Green
Mystic Gray Mystic Gray
Prussian Blue Prussian Blue
Pueblo Clay Pueblo Clay
Sage Sage
Soft Brick Soft Brick
Soft Platinum Soft Platinum

Please note, colors are RGB web approximations of the actual shades.

Downloads

Preparation

Surfaces must be thoroughly clean*. Using a pressure washer to clean the surface? Do not use a setting above 1750 psi, to avoid damaging the concrete. The surface must be thoroughly dry prior to painting. Surface porosity is important for proper product adhesion. For highly troweled or extremely smooth bare concrete, treat it with DRYLOK® Etch** (liquid or powder formula) or muriatic acid according to the manufacturer’s directions. Rinse the surface and allow it to dry.

Application

Schedule your project when both air and surface temperatures are above 50°F and, for best results, wait for a dry (rain-free) period. Avoid applying in direct sunlight. Stir thoroughly before and during application. When using 2 or more containers of the same color, mix them together to ensure color uniformity. On dry, windy days, lightly mist the surface with a pump sprayer to minimize lap marks. Apply 1 coat of DRYLOK® Concrete Stain & Toner using a brush, a quarter-inch or three-eighths-inch nap roller, a foam roller or a sprayer. If spraying, coats should be dry brushed or back rolled for a uniform appearance. Allow 1 hour drying time. One coat is required to achieve a semi-opaque, non-slip flat finish. An additional coat will produce a darker, more opaque color. On a more porous surface, an additional coat may be applied. DRYLOK® Concrete Stain & Toner may be used on unsealed, stamped concrete. The surface contour may cause the toner to puddle and require back brushing to eliminate the issue.

Allow to dry for 4 hours before subjecting to light foot traffic, and for 24 hours before subjecting to heavy foot traffic. Allow 5 days drying time before subjecting to automobile traffic. If a second coat is desired, allow the first coat to dry for 4 hours before applying.

DRYLOK® Concrete Stain and Toner may be topcoated with DRYLOK® WetLook High Gloss Sealer or DRYLOK® Concrete Protector for additional surface protection.

Disposal

Dispose of contaminated absorbent, container and unused contents in accordance with local, state and federal regulations.

USAGE STATEMENT: Prior to use, carefully read the product label and follow the directions. For technical information, warnings, cautions, notices, and additional information, download and read the documentation available on this website.

* WARNING: If you scrape, sand or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1-800-424-LEAD or visit www.epa.gov/lead.

** When using DRYLOK® Etch®, wear eye protection with side shields, chemical-resistant gloves, protective footwear and suitable clothing.