Cart

Subtotal
Total

DRYLOK® Fast Plug®

Quick setting hydraulic cement creates a watertight seal in 3 to 5 minutes. Works above and below ground level even with active leaks.

Shipping included. Taxes not included.

Regional shipping restrictions may apply.

Product Overview

A fast-setting hydraulic cement sets in just 3 – 5 minutes, preventing active or reoccurring water from flowing through cracks and holes in concrete and masonry structures.

Clean-up: Soap and water

Coverage: 16 In3

  • Easy mix, powder formula
  • Sets in 3 to 5 minutes (temperature of water or admix controls set time)
  • Use in waterproofing project to seal cracks, floor-wall joints, and utility entrance holes
  • No top coat required
  • CSI Masterformat® 03 01 00 Maintenance of Concrete
  • CSI Masterformat® 03 15 13 Waterstops
Click to expand / collapse
Surfaces
  • Concrete swimming pools
  • Basement floors
  • Drainage systems
  • Foundations
  • Elevator pits
  • Manholes
  • Sealing around concrete and masonry structures
Preparation

Wear eye protection, rubber gloves, and a dust mask when using DRYLOK® Fast Plug®. The area to be patched should be cleaned thoroughly by wire-brushing, scraping or any other effective process*. Back chisel out the area to be patched to the shape of an inverted V” (the point at the surface). This allows the patch to expand and lock into the surface. Wet the area prior to patching to help DRYLOK® Fast Plug® cure properly.

Both DRYLOK® Fast Plug® and water for mixing should be at room temperature. Mix 3 parts DRYLOK® Fast Plug® and 1 part water thoroughly until you achieve a putty or heavy troweling consistency. This mixture will set in 3 – 5 minutes. The use of colder water will retard the setting time. Mix only enough for immediate use due to the quick setting time. DRYLOK® Fast Plug® cannot be reworked once it has set. In cold weather, use warm (90°F) water for mixing; also, soak surface with warm water before application. Mix only enough for use in 3 minutes. Discard all leftover mixed patching material prior to starting a new batch. Leftover patching material will chemically react with new material in the mixing receptacle.

Application

For active leaks (the presence of flowing water through a break in the surface): mix the appropriate amount of DRYLOK® Fast Plug®. In approximately 2 – 3 minutes, the mixture will become warm to the touch. This means it is beginning to set. At this time, force DRYLOK® Fast Plug® into the opening with the palm of your hand. Hold it in place for 3 – 5 minutes to ensure a complete set and bond sufficient enough to stop the flow of water. The patched area may be smoothed and trimmed to the surrounding area in approximately 5 minutes. DRYLOK® Fast Plug® may be painted when set with DRYLOK® Original Masonry Waterproofer , DRYLOK® Extreme Masonry Waterproofer, DRYLOK® Powdered Masonry Waterproofer or DRYLOK® Concrete Floor Paint.

For Inactive Leaks, Patching, and Anchoring: thoroughly soak the area to be patched. This will prevent the surface from sucking the water out of the patching material. Apply DRYLOK® Fast Plug® with a putty knife or trowel. Use the surface to smooth the patch evenly. When anchoring, chisel or drill a hole in the masonry surface slightly larger than the item to be anchored. Make certain DRYLOK® Fast Plug® is tamped firmly into the hole and around any metal parts.

Cancer hazard: Contains Crystalline Silica, which can cause cancer**.

FAQs

Q. How do you recommend using DRYLOK® Fast Plug®?

A. Use on surfaces, cracks in walls, pools, wall joints and affixing objects that will be subjected to applied pressure.

Q. Can you use DRYLOK® Fast Plug® like any hydraulic cement?

A. Yes, DRYLOK® Fast Plug® is not only effective in the waterproofing process, but can be used for anchoring handrails, filling cracks and holes, and filling utility openings. 

USAGE STATEMENT: Prior to use, carefully read the product label and follow the directions. For technical information, warnings, cautions, notices, and additional information, download and read the documentation available on this website.

California Residents: Prop 65 WARNING(S)

* WARNING: If you scrape, sand or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1 – 800-424-LEAD or visit www​.epa​.gov/lead.

**Cancer hazard: Contains Crystalline Silica, which can cause cancer. Risk of cancer depends on duration and level of exposure to dust generated from sanding surfaces or grinding. Use only with adequate ventilation. Do not breathe dust. Avoid eye contact or prolonged contact with skin. Avoid exposure to dust by wearing an appropriate (NIOSH approved) particulate respirator during mixing, application and clean up. Follow respirator manufacturer’s directions for respirator use. Close container after each use. Avoid contact with eyes, skin and clothing. Wash thoroughly after handling.